Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Takei, Hayanori
Journal of Nuclear Science and Technology, 14 Pages, 2023/00
Times Cited Count：0 Percentile：0.08(Nuclear Science & Technology)In the proton linear accelerator (linac), the proton beam is unexpectedly interrupted due to the electrical discharge originating from the radio frequency, failure of the device/equipment, or other factors. Do these beam trips occur randomly? Conventionally, it has been implicitly assumed that beam trips occur randomly. In this study, we investigated whether beam trips in the linac of the Japan Proton Accelerator Research Complex (J-PARC) occur randomly to estimate the beam trip frequency in a superconducting proton linac for an accelerator-driven nuclear transmutation system. First, the J-PARC linac was classified into five subsystems. Then, the reliability function for the operation time in each subsystem was obtained using the Kaplan--Meier estimation, a reliability engineering methods. Using this reliability function, the randomness of beam trips was examined. Analysis of five-year operational data for five subsystems of the J-PARC linac showed that beam trips occurred randomly in some subsystems. However, beam trips did not occur randomly in many subsystems of the proton linac, including the ion source and the acceleration cavity, the primary subsystems of the proton linac.
CsShibahara, Yuji*; Nakamura, Shoji; Uehara, Akihiro*; Fujii, Toshiyuki*; Fukutani, Satoshi*; Kimura, Atsushi; Iwamoto, Osamu
Journal of Radioanalytical and Nuclear Chemistry, 325(1), p.155 - 165, 2020/07
Times Cited Count：8 Percentile：70.65(Chemistry, Analytical)The measurements of isotopic ratios of Cs samples by thermal ionization mass spectrometry were performed for the analysis of their samples used to evaluate nuclear data obtained for Cs. To obtain a high intensity and stable ion beam, the effects of additive agents on the ionization of Cs were examined. The effect of silicotungstic acid on the ionization of Cs was the largest among the additive agents studied in the present study, while the silicotungstic acid also showed the largest isobaric interference of polyatomic ions. It was demonstrated that as small as 2
10
g of a Cs sample was sufficient to achieve the analytical precision required to measure the Cs/
Cs ratio in the case where an additive agent of TaO/glucose was employed. After examining of the analytical conditions, such as the interference effect due to Ba, the measurements of the isotopic ratios of two Cs samples used in our study using TIMS were conducted, and it was discussed how much the ratios contributed to evaluation of the neutron capture cross-section of Cs.
Nakamura, Shoji; Shibahara, Yuji*; Kimura, Atsushi; Iwamoto, Osamu; Uehara, Akihiro*; Fujii, Toshiyuki*
Journal of Nuclear Science and Technology, 57(4), p.388 - 400, 2020/04
Times Cited Count：3 Percentile：31.36(Nuclear Science & Technology)The thermal-neutron capture cross-section (
) and resonance integral(I
) were measured for the Cs(n,
)
Cs reaction by an activation method and mass spectrometry. We used Cs contained as an impurity in a normally available Cs standard solution. An isotope ratio of Cs and Cs in a standard Cs solution was measured by mass spectrometry to quantify Cs. The analyzed Cs samples were irradiated at the hydraulic conveyer of the research reactor in Institute for Integral Radiation and Nuclear Science, Kyoto University. Wires of Co/Al and Au/Al alloys were used as neutron monitors to measure thermal-neutron fluxes and epi-thermal Westcott's indices at an irradiation position. A gadolinium filter was used to measure the , and a value of 0.133 eV was taken as the cut-off energy. Gamma-ray spectroscopy was used to measure induced activities of Cs, Cs and monitor wires. On the basis of Westcott's convention, the and I values were derived as 8.57
0.25 barn, and 45.33.2 barn, respectively. The obtained in the present study agreed within the limits of uncertainties with the past reported value of 8.30.3 barn.
Ohgama, Kazuya; Ota, Hirokazu*; Oki, Shigeo; Iizuka, Masatoshi*
Proceedings of 2019 International Congress on Advances in Nuclear Power Plants (ICAPP 2019) (Internet), 9 Pages, 2019/05
Hayashi, Hirokazu; Sato, Takumi; Shibata, Hiroki; Tsubata, Yasuhiro
NEA/NSC/R(2017)3, p.427 - 432, 2017/11
Transmutation of long-lived radioactive nuclides including minor actinides (MA: Np, Am, Cm) has been studied in Japan Atomic Energy Agency (JAEA). Pb-Bi cooled sub-critical accelerator-driven system (ADS) is regarded as one of the powerful tools for transmutation of MA under the double strata fuel cycle concept. Uranium-free MA-Pu nitride fuel was chosen as the first candidate for MA transmutation. Reprocessing of spent ADS fuel and reusing MA recovered from the spent ADS fuels is necessary to improve the transmutation ratio. A pyrochemical process has been proposed as the first candidate for reprocessing of the spent nitride fuel for MA transmutation, because this technique has some advantages over aqueous process, such as the resistance to radiation damage, which is an important issue for the fuels containing large amounts of highly radioactive MA, and feasibility for recovering expensive N-15 in the spent fuels to be reused. This paper overviews the current status of the technology development, including our recent study. Development of the anode suitable for electro-refining of nitride fuels and that of the apparatus for renitridation of the metals recovered in Cd cathode for 100g-Cd scale cold tests are main topics. Evaluation of the batch sizes of each process, which is necessary for estimating the scale of the engineering-apparatus, with considering the decay heat of MA and FP, will also be introduced.
inert matrix fuelMiwa, Shuhei; Osaka, Masahiko
Journal of Nuclear Materials, 487, p.1 - 4, 2017/04
Times Cited Count：4 Percentile：36.71(Materials Science, Multidisciplinary)Oxidation and reduction behaviors of prototypic MgO-based inert matrix fuels (IMFs) containing PuO were experimentally investigated by means of thermogravimetry. The oxidation and reduction kinetics of the MgO-PuO specimen were determined. The oxidation and reduction rates of the MgO-PuO were found to be low compared with those of PuO. It is note that the changes in O/Pu ratios of MgO-PuO from stoichiometry were smaller than those of PuO at high oxygen partial pressure. From these results, it can be said that MgO matrix lower the oxygen supply and release of PuO, which is preferable as the minor actinides incineration devices, since the high oxygen potentials of minor actinide oxides can cause certain problems in terms of thermochemical aspects such as enlarged cladding inner-surface corrosion.
Wan, T.; Obayashi, Hironari; Sasa, Toshinobu
Proceedings of 11th International Topical Meeting on Nuclear Reactor Thermal Hydraulics, Operation and Safety (NUTHOS-11) (USB Flash Drive), 12 Pages, 2016/10
Akimoto, Hajime; Sugawara, Takanori
JAEA-Data/Code 2016-008, 87 Pages, 2016/09
JAEA-Data-Code-2016-008.pdf:15.62MB
Thermal hydraulic behavior in a lead-bismuth cooled accelerator driven system (ADS) is analyzed under normal operation condition. Input data for the ADS version of J-TRAC code have been constructed to integrate the conceptual design. The core part of the ADS is modeled in detail to evaluate the core radial power profile effect on the core cooling. As the result of the analyses, the followings are found; (1) Both maximum clad temperature and fuel temperature are below the design limits. (2) The radial power profile has little effect on the coolant flow distribution among fuel assemblies. (3) The radial power profile has little effect on the heat transfer coefficients along fuel rods. (4) The thermal hydraulic behaviors along four steam generators are identical. The thermal hydraulic behaviors along two pumps are also identical. A fast running input data is developed by the simplification of the detailed input data based on the findings mentioned above.
Yokoyama, Kenji; Maruyama, Shuhei; Numata, Kazuyuki; Ishikawa, Makoto; Takeda, Toshikazu*
Proceedings of International Conference on the Physics of Reactors; Unifying Theory and Experiments in the 21st Century (PHYSOR 2016) (USB Flash Drive), p.1906 - 1915, 2016/05
Takeda, Toshikazu*; Usami, Shin; Fujimura, Koji*; Takakuwa, Masayuki*
Proceedings of 21st International Conference & Exhibition; Nuclear Fuel Cycle for a Low-Carbon Future (GLOBAL 2015) (USB Flash Drive), p.560 - 566, 2015/09
The Ministry of Education, Culture, Sports, Science and Technology in Japan has launched a national project entitled "technology development for the environmental burden reduction" in 2013. The present study is one of the studies adopted as the national project. The objective of the study is the efficient and safe transmutation and volume reduction of minor actinides with long-lived radioactivity and high decay heat contained in high level radioactive wastes by using sodium cooled fast reactors. We are developing MA transmutation core concepts which harmonize efficient MA transmutation with core safety. To accurately design the core concepts we have improved calculation methods for estimating the transmutation rate of individual MA nuclides, and estimating and reducing uncertainty of MA transmutation. The overview of the present project is first described. The method improvement is presented with numerical results for a minor-actinide transmutation fast reactor.
Akimoto, Hajime
JAEA-Data/Code 2014-031, 75 Pages, 2015/03
JAEA-Data-Code-2014-031.pdf:37.23MB
A thermal-hydraulic analysis code for transmutation system with lead-bismuth cooled accelerator-driven system (ADS) has been developed using the Japanese-version of Transient Reactor Analysis Code (J-TRAC) as the framework to apply the design studies of ADS. To identify the required capabilities of the thermal-hydraulic analysis code for ADS, previous thermal-hydraulic analyses of light water reactors, sodium-cooled fast reactor and ADS have been surveyed. To make up for insufficient capabilities of the J-TRAC code as a thermal-hydraulic analysis code of ADS, physical properties of lead-bismuth eutectic (LBE), argon gas and nitride nuclear fuel were implemented to the J-TRAC code. It was confirmed that the implemented capabilities worked as expected through verification calculations on (1) single-phase LBE flow, (2) heat transfer in a fuel assembly, and (3) heat transfer in a steam generator.
Oigawa, Hiroyuki; Sasa, Toshinobu; Kikuchi, Kenji; Nishihara, Kenji; Kurata, Yuji; Umeno, Makoto*; Tsujimoto, Kazufumi; Saito, Shigeru; Futakawa, Masatoshi; Mizumoto, Motoharu; et al.
Proceedings of 4th International Workshop on the Utilisation and Reliability of High Power Proton Accelerators, p.507 - 517, 2005/11
Under the framework of J-PARC, the Japan Atomic Energy Research Institute (JAERI) plans to construct the Transmutation Experimental Facility (TEF). The TEF consists of two facilities: the Transmutation Physics Experimental Facility (TEF-P) and the ADS Target Test Facility (TEF-T). The TEF-P is a critical facility which can accept a 600 MeV - 10 W proton beam. The TEF-T is a material irradiation facility using a 600 MeV - 200 kW proton beam, where a Pb-Bi target is installed, but neutron multiplication by nuclear fuel will not be attempted. This report describes the purposes of the facility, the present status of the conceptual design, and the expected experiments to be performed.
Oigawa, Hiroyuki; Tsujimoto, Kazufumi; Kikuchi, Kenji; Kurata, Yuji; Sasa, Toshinobu; Umeno, Makoto*; Nishihara, Kenji; Saito, Shigeru; Mizumoto, Motoharu; Takano, Hideki*; et al.
Proceedings of 4th International Workshop on the Utilisation and Reliability of High Power Proton Accelerators, p.325 - 334, 2005/11
The Japan Atomic Energy Research Institute (JAERI) is conducting the research and development (R&D) on the Accelerator-Driven Subcritical System (ADS) for the effective transmutation of minor actinides (MAs). The ADS proposed by JAERI is the 800 MWth, Pb-Bi cooled, tank-type subcritical reactor loaded with (MA+Pu) nitride fuel. The Pb-Bi is also used as the spallation target. In this study, the feasibility of the ADS was discussed with putting the focus on the design around the beam window. The partition wall was placed between the target region and the ductless-type fuel assemblies to keep the good cooling performance for the hot-spot fuel pin. The flow control nozzle was installed to cool the beam window effectively. The thermal-hydraulic analysis showed that the maximum temperature at the outer surface of the beam window could be repressed below 500 
C even in the case of the maximum beam power of 30 MW. The stress caused by the external pressure and the temperature distribution of the beam window was also below the allowable limit.
Arai, Yasuo; Minato, Kazuo
Journal of Nuclear Materials, 344(1-3), p.180 - 185, 2005/09
Times Cited Count：24 Percentile：81.96(Materials Science, Multidisciplinary)no abstracts in English
Kiyanagi, Yoshiaki*; Nagamiya, Shoji*; Oyama, Yukio; Ikeda, Yujiro; Oigawa, Hiroyuki; Igashira, Masayuki*; Baba, Mamoru*; Iwasaki, Tomohiko*; Watanabe, Yukinobu*; Ishibashi, Kenji*
Nihon Genshiryoku Gakkai-Shi, 46(3), p.173 - 197, 2004/03
no abstracts in English
Department of Nuclear Energy System
JAERI-Review 2002-005, 280 Pages, 2002/03
JAERI-Review-2002-005.pdf:18.05MB
no abstracts in English
I using an accelerator-driven systemNishihara, Kenji; Takano, Hideki
Nuclear Technology, 137(1), p.47 - 59, 2002/01
Times Cited Count：4 Percentile：29.2(Nuclear Science & Technology)no abstracts in English
Minato, Kazuo; Arai, Yasuo; Akabori, Mitsuo; Nakajima, Kunihisa
Proceedings of American Nuclear Society Conference "Nuclear Applications in the New Millennium" (AccApp-ADTTA '01) (CD-ROM), 6 Pages, 2002/00
In the Japan Atomic Energy Research Institute (JAERI), the concept of the transmutation of minor actinides (MA: Np, Am and Cm) with accelerator-driven systems (ADS) is being studied, where MA nitride is adopted as a fuel material of sub-critical core. The nitride fuel has been chosen as a candidate because of the possible mutual solubility among the actinide mononitrides and excellent thermal properties besides supporting hard neutron spectrum. Highly enriched N-15 would have to be used for the nitride fuel in order to prevent the formation of hazardous C-14. By applying pyrochemical process in the treatment of spent fuel, N-15 could be readily recovered and recycled. The present paper describes an overview of the research on the nitride fuel performed in JAERI. Fabrication experiments of actinide nitrides, measurements of vaporization behavior and thermal properties, and irradiation tests of actinide nitrides are summarized.
Nishihara, Kenji; Ando, Yoshihira*; Takano, Hideki
JAERI-Research 99-074, p.24 - 0, 2000/01
JAERI-Research-99-074.pdf:1.05MB
no abstracts in English
JAERI-Conf 99-003, 215 Pages, 1999/03
no abstracts in English
